EK-M21
High-temperature boron-nitride oil-based mold release agent
Boron-nitride-modified oil-based release agent for high-temperature moulds and tooling; usable from ambient temperature up to 1500 °C.
FORM
Oil-based release agent
APPEARANCE
Black liquid
CURING
Ready 1–2 min after spraying
Documents
TDS · SDS
Adhesives
The material
How this grade works and where it fits — exact parameters are defined in the TDS.
This product is a high-temperature-resistant release agent modified with boron nitride using a series of nanotechnologies. The coating exhibits excellent toughness, hardness, adhesion, anti-stick and anti-yellowing performance, with adhesion of Grade 1 (cross-cut), and provides a semi-permanent release effect.
The product is non-toxic and environmentally friendly and complies with RoHS and other relevant standards. It effectively solves mold-release problems in the forming of a wide range of materials and is widely used in mold release and many related fields.
Choose this grade as a boron-nitride-modified oil-based release agent for high-temperature moulds and tooling — usable from ambient temperature up to 1500 °C, ready 1–2 minutes after spraying.
Final fit is confirmed during technical review — send your substrate, operating environment and application process, and the team will confirm this grade or point you to a closer one.
Suitable for
Industrial applications within the TDS parameters
Metal, glass, ceramic and stone substrates — per grade
Professional application and curing processes
Not intended for
Consumer or DIY use — industrial B2B supply only
Conditions outside the parameters defined in the TDS
Food-contact or medical use unless explicitly confirmed
Applications
Recommended application areas for this grade, based on its TDS. Application fit is confirmed during technical review.
Mould and tooling release in high-temperature processes — application guidance on request.
Technical data
Key values from this grade's TDS. The complete measured data set follows below; the official document is available on request.
PROPERTY
TYPICAL VALUE
NOTES
Solid content
>55%
—
Viscosity
400–600 s
—
Max service temperature
Ambient up to 1500 °C
Depends on cure & film build
Curing conditions
Ready 1–2 min after spraying
Per application process
Recommended film thickness
Not applicable (release agent)
—
Shelf life
12 months (storage at -20 °C to +50 °C)
Storage conditions apply
Service temperature. This product can be used in applications from ambient temperature up to 1500 °C. After spraying, it only needs to stand for 1–2 minutes before use. The cured coating has excellent adhesion, good anti-stick performance and anti-fingerprint performance.
Coating Film Properties
State: One-component
Color and appearance: Black liquid — GB-T 1721-79
Solids content ((120±2) °C): >55% — GB/T 1725-2007
Density (ph): 0.83±0.02 — GB/T 6750-2007
Adhesion: Grade 1 (cross-cut) — GB-T 9286-1998
Viscosity (Cs): 400–600 — GB-T 10125-2021
Flash point: >200 °C
Data above is taken from the manufacturer’s TDS. Request the official document via the documents section below.
Substrates & storage
Compatibility and handling essentials — confirmed per grade in the TDS and SDS.
Suitable substrates
Steel and stainless steel
Aluminium and other metals
Glass and ceramics
Stone and mineral surfaces
Stainless steel, glass (flat glass, glass bottles, etc.), cast iron, aluminum alloys, titanium alloys, high-temperature alloy steels, glass-ceramic plates, ceramics, photovoltaic glass panels and other such materials are all suitable. Note: The coating formulation differs for different substrates; within a certain range it can be adjusted and matched to the substrate and its specific service conditions.
Storage, packaging & transport
Store in accordance with national regulations. The storage environment should be dry, cool and well ventilated, away from heat and ignition sources. Packaging containers must be kept tightly closed and placed with care.
The storage temperature should be maintained at -20 °C to +50 °C; the shelf life is 12 months.
Opened, partly used material must be stored with the container lid tightly resealed.
Prepared material that is not used up cannot be reclaimed and should be disposed of in accordance with local regulations.
Product past its shelf life may be used only after testing confirms it still meets specifications.
Packaging
1 kg / 5 kg / 25 kg (grade-dependent)
Transport classification
Per SDS
Application process
General guidance — exact parameters are provided in the TDS and Application Guide.
01
Surface preparation
Clean, degrease and prepare the substrate.
02
Application
Spray, dip or wipe depending on grade.
03
Curing
Cure per the TDS conditions.
04
Quality control
Verify film build and adhesion.
Preparation. Stir the release agent thoroughly before use. At the same time, clean the mold surface, removing oil, rust, debris and residual contamination, to ensure the mold surface is clean and dry.
Spray application. Spray the release agent onto the mold surface from a distance of 20–30 cm, applying in even, constant-speed passes. Ensure the mold forming surface is completely covered, forming a thin, uniform release layer.
Standing before use. After spraying is complete, let stand for 1–2 minutes so that the release agent adheres fully to the mold surface and forms a stable film; subsequent forming operations can then be carried out.
Note. This product settles during prolonged storage; stir thoroughly with a mixer before use.
More grades
Browse the full catalogue by category, or send your requirements — we will recommend a grade for your case.
Organic Polysilazane Resins
→
Inorganic Polysilazane / Ceramic Precursors
→
Modified Polysilazane Coatings
→
Ready-to-use Ceramic Coatings
→
High-temperature Ceramic Coatings
→
Electrical Insulation Coatings
→
Fluorosilanes & Surface Modifiers
→
Adhesives
→
Additives
→
Polycarbosilane
→
SiC Fibers
→
Ordering & logistics
Common questions from procurement and engineering teams.
What packaging formats are available?
Standard packaging is 1 kg, 5 kg and 25 kg containers, grade-dependent. Other formats, minimum order quantity, lead times, shipping terms and stock availability are confirmed on request.
What is the minimum order quantity for this product?
MOQ depends on the packaging format — confirmed by our team for your grade and volume.
What happens after I send an inquiry?
Our technical team reviews your requirement and responds with a recommendation, the relevant documents and next steps.
How do I get a quotation?
Include your estimated volume and application in the inquiry — a quotation follows the technical review.
How is the product shipped?
Packaging, transport classification and shipping details are provided per SDS — request packaging and shipping information with your inquiry.