Anti-corrosion Coatings
Protect metal and concrete against moisture, salt and chemical exposure with polysilazane-based coating systems. We don’t promise a universal result — we recommend a specific material for your substrate and environment, confirmed by documentation and a sample.
Recommended products
Proposed starting points — the final recommendation for your case follows technical review.
EK-D06
→
Room-temperature curing insulation coating
Insulation voltage-resistant coating curing at room temperature.
EK-D07
→
Insulating anti-corrosion blue film
Heat-resistant insulating anti-corrosion blue film; room-temperature curing.
EK-M01
→
Epoxy-modified silazane coating
Paint and coating protection; room-temperature application, short-term up to 500 °C.
EK-M06
→
One-component polyester-modified polysilazane resin
Polyester-modified polysilazane resin addressing toughness and bend resistance.
EK-M102
→
Fluorine-modified polysilazane, 28–30% fluorine
Fluorine-modified polysilazane from the methyl trifluoropropyl series; 28–30% fluorine, water contact angle 105–110°.
EK-M103
→
Fluorine-modified polysilazane, 55–60% fluorine
Highest-fluorine grade in the range — 55–60% fluorine and a water contact angle of 110–120° for superhydrophobic surfaces.
EK-S01
→
Room-temperature curing transparent silazane varnish
Transparent RT-curing varnish for electronics, easy-clean and outdoor anti-corrosion.
EK-S06
→
Polyborosilazane resin
Film-former for self-cleaning anti-corrosive coatings; air cure below 200 °C, >6H.
EK-S07
→
High- and low-temperature heavy-duty anticorrosive fluorosilicone coating
Heavy-duty anti-corrosion resin with low-temperature application; fiber sizing agent.
EK-S1000
→
High-viscosity polysilazane for thick-film industrial coatings
High-viscosity heat-curing polysilazane for films 0.1–0.4 mm thick; 1000 °C peak service after ceramisation.
EK-S13
→
High- and low-temperature resistant anticorrosive coating
One-component anticorrosive coating: 5000 h salt spray, −50…280 °C service.
EK-S1303
→
Solvent-based polysilazane, full cure in one day
Solvent-based low-viscosity polysilazane with the fastest full cure in the range — one day — and contact angle 105–110°.
EK-S1502
→
Solvent-based ultra-fast-curing polysilazane resin
Solvent-based low-viscosity polysilazane; tack-free in 20–30 minutes, 7–8H hardness, water contact angle 98–104°.
MIR 336 Metal · Transparent
→
Ready-to-use polysilazane coating for metal
Protective coating against oxidation and corrosion for copper, brass, bronze, stainless steel, aluminium and silver. Transparent gloss finish.
MIR 336 Matt
→
Ready-to-use polysilazane coating for stone and metal — matt
Protective coating for stone and metal with a matt finish; repels water, oil and dirt and protects against oxidation and corrosion.
MIR 336 Semi-matt
→
Ready-to-use polysilazane coating for stone and metal — semi-matt
Protective coating for stone and metal with a semi-matt finish; repels water, oil and dirt and protects against oxidation and corrosion.
MIR 337 Metal · Transparent
→
Ultra-thin polysilazane coating for polished metal
Transparent coating for polished and mirror-finish metal; applied with polishing to a 0.1 µm film that leaves the reflection untouched.
MIR 337 Matt
→
Ultra-thin polysilazane coating for stone and metal — matt
Ultra-thin coating for stone and metal with a matt finish; applied with polishing to a 0.1 µm film.
MIR 337 Semi-matt
→
Ultra-thin polysilazane coating for stone and metal — semi-matt
Ultra-thin coating for stone and metal with a semi-matt finish; applied with polishing to a 0.1 µm film.
The challenge
Recognise your situation — and what it costs when protection fails.
Moisture, salts and chemicals attack metal and concrete surfaces continuously. When a protective layer fails, the cost is not just repainting — it is downtime, part replacement and safety risk.
Conventional organic paints have limits in aggressive environments. Silazane-based systems form a dense protective layer designed for longer service in these conditions — the right grade and film build are confirmed during technical review.
Typical situations
Coastal and marine environments — salt spray and humidity
Chemical processing — acids, alkalis and solvents
Outdoor steel structures and infrastructure
Storage tanks, pipelines and process equipment
How the protection works
Ceramic protection layer
Dense barrier against moisture, salts and chemicals
Polysilazane layer
Adhesion, curing and surface conversion
Substrate
Steel, aluminium, concrete or mineral surface
Requirements
Properties that matter for corrosion protection — availability depends on product grade and is confirmed in the TDS.
Barrier against moisture & salts
Dense layer limiting water and ion penetration.
Chemical resistance
Withstands acids, alkalis and solvents — per grade.
Adhesion to metal & concrete
Reliable bonding to prepared substrates.
Abrasion & wear resistance
Keeps the barrier intact under mechanical load.
Thermal stability
Where heat is part of the environment.
Long-term durability
Designed for extended service — validated on your parts.
Substrates & industries
Where these systems are typically applied. Compatibility is confirmed per grade — not guaranteed generically.
Typical substrates
Carbon and stainless steel
Aluminium and galvanized surfaces
Concrete and mineral substrates
Prepared / primed surfaces per guide
Typical industries
Marine, ports and coastal infrastructure
Chemical and process industry
Energy and utilities
Construction and civil infrastructure
FAQ
Common questions about anti-corrosion coating projects.
Can the coating be applied to an already corroded surface?
Surface preparation requirements — including rust removal — are defined in the Application Guide. The condition of your surface is assessed during technical review.
How is this different from conventional anti-corrosion paint?
Silazane-based systems form a dense ceramic-like layer designed for aggressive environments. Comparative data for a specific grade is available on request.
How long will the protection last?
Service life depends on the environment, film build and application quality — we validate it on your parts through sample testing rather than promising generic numbers.
Which product should I start with?
Send your substrate, environment and process — our team will recommend a grade and provide the TDS. Custom formulation is possible subject to technical review.
Can I test before committing to volume?
Yes — sample support is available for qualified B2B projects after a short technical review.
What about MOQ and pricing?
Both depend on the grade, packaging and volume — include your estimated quantity in the request and a quotation follows the technical review.
Send request
From first enquiry to qualified bulk supply — send your requirements below.
01
Send requirement
Application, substrate and performance target.
02
Get recommendation
Suitable material family and product grade.
03
Receive TDS/SDS, catalog & sample
Documentation and sample for evaluation.
04
Test material
Validate on your substrate and process.
05
Confirm & bulk supply
Specification agreement and ongoing supply.
About anti-corrosion coatings
Anti-corrosion coatings protect metal and concrete assets against moisture, salts and chemicals in industrial environments. Polysilazane-based systems form a dense protective layer for aggressive service conditions.