EK-S02.1500 RC
Room-temperature fast-curing polysilazane resin
Solvent-free liquid polysilazane, fast ambient moisture cure; 6–8H, water contact angle 100–110°.
FORM
Solvent-free liquid resin (100% active)
APPEARANCE
Colorless to pale-yellow clear liquid
CURING
Ambient moisture cure · surface-dry 20–60 min · full cure 3–7 days
Documents
TDS · SDS
Curing agent / resin modifier (phenolic, epoxy, alkyd, acrylic)
The material
How this grade works and where it fits — exact parameters are defined in the TDS.
Solvent-free, low-viscosity liquid polysilazane resin, used for heat-resistant, scratch-resistant and hydrophobic coatings.
EK-S02.1500 RC is the same product as Durazane 1500RC.
Applications
Scratch-resistant coatings for automotive interiors and exteriors
Hydrophobic and water-repellent coatings for construction, consumer goods and transport
Suitable for metal, glass and plastic substrates
Choose this grade when the coating must cure at room temperature and be handled quickly: fast moisture cure, 6–8H pencil hardness and a 100–110° water contact angle. The slow-cure counterpart is EK-S02.1500 SC.
Final fit is confirmed during technical review — send your substrate, operating environment and application process, and the team will confirm this grade or point you to a closer one.
Suitable for
Industrial applications within the TDS parameters
Metal, glass, ceramic and stone substrates — per grade
Professional application and curing processes
Not intended for
Consumer or DIY use — industrial B2B supply only
Conditions outside the parameters defined in the TDS
Food-contact or medical use unless explicitly confirmed
Applications
Recommended application areas for this grade, based on its TDS. Application fit is confirmed during technical review.
Recommended applications for this grade:
Technical data
Key values from this grade's TDS. The complete measured data set follows below; the official document is available on request.
PROPERTY
TYPICAL VALUE
NOTES
Solid content
100%
—
Viscosity
20–40 cSt (25 °C)
—
Max service temperature
<500 °C in air
Depends on cure & film build
Curing conditions
Ambient moisture cure · surface-dry 20–60 min · full cure 3–7 days
Per application process
Recommended film thickness
4–6 µm (test film)
—
Shelf life
12 months (cool, dry storage)
Storage conditions apply
General description. Solvent-free, low-viscosity liquid polysilazane resin for heat-resistant, scratch-resistant and hydrophobic coatings.
Features
Cures by ambient moisture or by heat
Good adhesion and hydrophobicity
Good weathering, chemical and UV resistance
Higher crosslink density than EK-S02.1500 SC
Technical Data
Appearance: Colorless to pale-yellow clear liquid
Viscosity (25 °C): 20–40 cSt
Active content: 100%
Pencil hardness: 6–8H
Adhesion: Grade 0
Water contact angle: 100–110°
Heat resistance (air): <500 °C
Shelf life: 1 year
Test conditions: 304 stainless steel substrate, blade-coated, fully cured at room temperature, film thickness 4–6 µm. Stored cool and dry.
Data above is taken from the manufacturer’s TDS. Request the official document via the documents section below.
Substrates & storage
Compatibility and handling essentials — confirmed per grade in the TDS and SDS.
Suitable substrates
Steel and stainless steel
Aluminium and other metals
Glass and ceramics
Stone and mineral surfaces
Suitable for metal, glass and plastic substrates.
Storage, packaging & transport
Use in a well-ventilated area.
Close the container immediately after use, to prevent contaminants and water vapour from entering the product.
Store containers in a cool, dry, well-ventilated place.
Shelf life: 1 year.
Packaging: 1 L and 5 L aluminium bottles; 25 L and 200 L PE-lined steel drums; custom sizes on request.
Packaging
1 kg / 5 kg / 25 kg (grade-dependent)
Transport classification
Per SDS
Application process
General guidance — exact parameters are provided in the TDS and Application Guide.
01
Surface preparation
Clean, degrease and prepare the substrate.
02
Application
Spray, dip or wipe depending on grade.
03
Curing
Cure per the TDS conditions.
04
Quality control
Verify film build and adhesion.
Application methods: Spin coating, wipe coating, dip coating, spraying, brushing or roller coating.
Curing: Surface-dry in 20–60 minutes at room temperature; full cure in 3–7 days.
More grades
Browse the full catalogue by category, or send your requirements — we will recommend a grade for your case.
Organic Polysilazane Resins
→
Inorganic Polysilazane / Ceramic Precursors
→
Modified Polysilazane Coatings
→
Ready-to-use Ceramic Coatings
→
High-temperature Ceramic Coatings
→
Electrical Insulation Coatings
→
Fluorosilanes & Surface Modifiers
→
Adhesives
→
Additives
→
Polycarbosilane
→
Cyclosilazanes
→
Silazane Monomers
→
SiC Fibers
→
Ordering & logistics
Common questions from procurement and engineering teams.
What packaging formats are available?
Standard packaging is 1 kg, 5 kg and 25 kg containers, grade-dependent. Other formats, minimum order quantity, lead times, shipping terms and stock availability are confirmed on request.
What is the minimum order quantity for this product?
MOQ depends on the packaging format — confirmed by our team for your grade and volume.
What happens after I send an inquiry?
Our technical team reviews your requirement and responds with a recommendation, the relevant documents and next steps.
How do I get a quotation?
Include your estimated volume and application in the inquiry — a quotation follows the technical review.
How is the product shipped?
Packaging, transport classification and shipping details are provided per SDS — request packaging and shipping information with your inquiry.