EK-S1302
Flexible heat-curing polysilazane for resin modification
Heat-curing binder for modifying silicone, epoxy, acrylic and polyurethane resins; flexible film, contact angle 102–105°.
FORM
Solvent-free liquid resin · heat cure only
APPEARANCE
Colourless to pale yellow clear liquid
CURING
200 °C tack-free 4 h, then 7–15 days at room temperature
Documents
TDS · SDS
The material
How this grade works and where it fits — exact parameters are defined in the TDS.
Low-viscosity liquid polysilazane resin used as a coating binder and for resin modification. It reacts with epoxy, isocyanate, alcohol, ketone, amine and phenolic groups, which makes it suitable as the base of hybrid systems. The cured film is deliberately soft — 5B–3B on the pencil scale — so it stays flexible rather than hard.
Choose this grade to add polysilazane chemistry — hydrophobicity, weathering and thermal resistance — to an existing resin system without making the film brittle. It is a modifier first and a standalone coating second.
Suitable for
Industrial applications within the TDS parameters
Metal, glass, ceramic and stone substrates — per grade
Professional application and curing processes
Not intended for
Consumer or DIY use — industrial B2B supply only
Conditions outside the parameters defined in the TDS
Food-contact or medical use unless explicitly confirmed
Applications
Recommended application areas for this grade, based on its TDS. Application fit is confirmed during technical review.
Hydrophobic and water-repellent coatings in construction, consumer products and transport. Modification of silicone, epoxy, acrylic and polyurethane resins.
Technical data
Key values from this grade's TDS. The complete measured data set follows below; the official document is available on request.
PROPERTY
TYPICAL VALUE
NOTES
Solid content
100% active
—
Viscosity
20–40 cSt (25 °C)
—
Max service temperature
500 °C in air
Depends on cure & film build
Curing conditions
200 °C tack-free 4 h, then 7–15 days at room temperature
Per application process
Recommended film thickness
4–6 µm (test film)
—
Shelf life
12 months (cool, dry storage)
Storage conditions apply
Pencil hardness 5B–3B. Adhesion grade 0. Water contact angle 102–105°. Heat resistance below 500 °C in air. Shelf life 12 months. Values measured on a glass substrate, blade-coated and air-dried, film thickness 4–6 µm.
Data above is taken from the manufacturer’s TDS. Request the official document via the documents section below.
Substrates & storage
Compatibility and handling essentials — confirmed per grade in the TDS and SDS.
Suitable substrates
Steel and stainless steel
Aluminium and other metals
Glass and ceramics
Stone and mineral surfaces
Suitable for metal, glass and plastic substrates.
Storage, packaging & transport
Use in a well-ventilated area. Close the container immediately after use to keep contaminants and moisture out of the product. Store in a cool, dry, well-ventilated place. Shelf life 12 months. Supplied in 1 L and 5 L aluminium bottles and in 25 L and 200 L PE-lined steel drums; custom packaging on request.
Packaging
1 kg / 5 kg / 25 kg (grade-dependent)
Transport classification
Per SDS
Application process
General guidance — exact parameters are provided in the TDS and Application Guide.
01
Surface preparation
Clean, degrease and prepare the substrate.
02
Application
Spray, dip or wipe depending on grade.
03
Curing
Cure per the TDS conditions.
04
Quality control
Verify film build and adhesion.
Application methods: spin, wipe, dip, spray, brush and roller coating.
More grades
Browse the full catalogue by category, or send your requirements — we will recommend a grade for your case.
Organic Polysilazane Resins
→
Inorganic Polysilazane / Ceramic Precursors
→
Modified Polysilazane Coatings
→
Ready-to-use Ceramic Coatings
→
High-temperature Ceramic Coatings
→
Electrical Insulation Coatings
→
Fluorosilanes & Surface Modifiers
→
Adhesives
→
Additives
→
Polycarbosilane
→
Cyclosilazanes
→
Silazane Monomers
→
SiC Fibers
→
Ordering & logistics
Common questions from procurement and engineering teams.
What packaging formats are available?
Standard packaging is 1 kg, 5 kg and 25 kg containers, grade-dependent. Other formats, minimum order quantity, lead times, shipping terms and stock availability are confirmed on request.
What is the minimum order quantity for this product?
MOQ depends on the packaging format — confirmed by our team for your grade and volume.
What happens after I send an inquiry?
Our technical team reviews your requirement and responds with a recommendation, the relevant documents and next steps.
How do I get a quotation?
Include your estimated volume and application in the inquiry — a quotation follows the technical review.
How is the product shipped?
Packaging, transport classification and shipping details are provided per SDS — request packaging and shipping information with your inquiry.