MIR 336
Ready-to-use polysilazane coating for metal
Transparent protective coating against oxidation and corrosion for copper, brass, bronze, stainless steel, aluminium and silver.
FORM
One-component ready-to-use coating
APPEARANCE
Colourless to pale yellow liquid
CURING
Ambient moisture cure. Surface dry approx. 3 h. Water resistance: 24 h at 5–12 °C · 12 h at 20–30 °C · 2 h at 80 °C · 1 h at 130–180 °C. Full properties after 5–7 days.
Documents
TDS · SDS
The material
How this grade works and where it fits — exact parameters are defined in the TDS.
MIR 336 is a transparent, colourless, ready-to-use coating built on a patented polysilazane technology. On application it forms a dense barrier layer that bonds chemically to the substrate rather than sitting on top of it. Curing takes place at room temperature in the presence of atmospheric humidity, so no oven or additional equipment is required.
The cured film is free of fluorine-containing components. It resists aggressive chemical reagents including solvents and alkalis, holds up under prolonged sunlight, and can be cleaned repeatedly without reapplying the protective layer. Removal is possible by mechanical means only — abrasive systems or comparable tooling — which is a direct consequence of its chemical resistance.
Choose this grade to protect decorative and structural metal while keeping the original surface visible: a transparent film that bonds chemically to the substrate, cures at ambient temperature and withstands 2400 h of salt spray on aluminium. Note that it is alkali-resistant but not sufficiently acid-resistant.
Clean with products in the pH 4–10 range. Strong inorganic acids and alkali metals must not contact the coating, as they break down the molecular structure of the protective layer. For heavier soiling such as graffiti use the CB 120 solvent degreaser, the IPA alcohol degreaser, or surfactant-based household cleaners; 646-series industrial thinner removes stubborn residues but should be used briefly and with care. Correctly applied, the coating has a service life of five years or more.
Suitable for
Industrial applications within the TDS parameters
Metal, glass, ceramic and stone substrates — per grade
Professional application and curing processes
Not intended for
Consumer or DIY use — industrial B2B supply only
Conditions outside the parameters defined in the TDS
Food-contact or medical use unless explicitly confirmed
Applications
Recommended application areas for this grade, based on its TDS. Application fit is confirmed during technical review.
Recommended for metal surfaces requiring long-term protection from corrosion, oxidation, aggressive chemical exposure and staining: outdoor and indoor furniture, decorative elements, architectural metalwork and structural components. Salt-spray and condensing-humidity testing over 100 days supports use in marine, industrial and demanding climatic conditions.
Technical data
Key values from this grade's TDS. The complete measured data set follows below; the official document is available on request.
PROPERTY
TYPICAL VALUE
NOTES
Solid content
Organic polysilazane binder in n-butyl acetate · flash point below 21 °C
—
Viscosity
Not stated in the technical description
—
Max service temperature
Weathering: 2000 h filtered xenon-arc exposure per DIN EN ISO 11341 with approx. 92–93 % gloss retention
Depends on cure & film build
Curing conditions
Ambient moisture cure. Surface dry approx. 3 h. Water resistance: 24 h at 5–12 °C · 12 h at 20–30 °C · 2 h at 80 °C · 1 h at 130–180 °C. Full properties after 5–7 days.
Per application process
Recommended film thickness
Up to 2 µm nominal dry film. Measured on test panels: 10 ± 0.5 µm (MEGA-CHECK FN2189); adhesion specimens ranged 9.6–11.9 µm. Both figures are reproduced as given in the technical description.
—
Shelf life
24 months from delivery, sealed container at up to +20 °C
Storage conditions apply
Adhesion grade 0 (GOST 31149-2014). Pencil hardness 9H for the gloss grade and 6H for the semi-matt grade (GOST 54586-2011). Impact resistance 50 cm direct and reverse (GOST 4765-2024). Bending elasticity over a 1 mm mandrel without damage (GOST 6806-2024). Water contact angle 103.95 ± 2.42° measured on a Kruss DSA instrument, with a total surface energy of 15.37 ± 1.06 mJ/m²; the technical description separately states 95° for the standard version, extendable to 120° with modifiers. Drying to grade 3 in 3 hours (GOST 19007-2023).
Corrosion testing: aluminium withstood 100 days (2400 h) of neutral salt spray to ISO 7253:1996 with no signs of corrosion; steel withstood 100 days (2400 h) of condensing humidity to ISO 6270-2:2005 with no damage.
Chemical resistance to GOST 9.403-2022, one hour of static exposure: sunflower oil, wine and alkaline household cleaner produced no change. Table vinegar at 9 % left a mark after 20 minutes and removed the coating after 30 minutes. The coating is therefore alkali-resistant but not sufficiently acid-resistant.
Data above is taken from the manufacturer’s TDS. Request the official document via the documents section below.
Substrates & storage
Compatibility and handling essentials — confirmed per grade in the TDS and SDS.
Suitable substrates
Steel and stainless steel
Aluminium and other metals
Glass and ceramics
Stone and mineral surfaces
Metals including aluminium, zinc, stainless steel, copper, brass, bronze and silver. The coating also performs on smooth non-absorbent surfaces, painted surfaces based on one- or two-component polyurethane and epoxy systems, polyester coatings, glass-reinforced plastic, concrete, glass, plastics and ceramics.
Storage, packaging & transport
Store in a tightly closed container in a cool, dry, well-ventilated place away from heat, sparks and open flame. Flash point below 21 °C — flammable liquid. Shelf life 24 months from delivery at up to +20 °C in sealed packaging. Supplied in 15 ml, 50 ml, 100 ml, 500 ml and 1 L containers.
Packaging
1 kg / 5 kg / 25 kg (grade-dependent)
Transport classification
Per SDS
Application process
General guidance — exact parameters are provided in the TDS and Application Guide.
01
Surface preparation
Clean, degrease and prepare the substrate.
02
Application
Spray, dip or wipe depending on grade.
03
Curing
Cure per the TDS conditions.
04
Quality control
Verify film build and adhesion.
Shake the container thoroughly before use. Apply with a microfibre applicator, technical chamois, roller or brush, by dipping, or with spray equipment. For spraying use an LVLP or HVLP gun on compressed air at 2–3 bar with a 0.8–1.3 mm nozzle, and clean the gun immediately after work with butyl acetate or 646 thinner. Several coats may be applied at five-minute intervals.
Work at an ambient temperature of at least +5 °C and a relative humidity of 30–85 %, keeping the surface out of direct sunlight and protected from rain. Substrate temperature at preparation and application must be between +5 °C and +30 °C.
Surface preparation: mechanical cleaning of loose contamination with a brush or compressed air, then degreasing. For mineral, glass and metal surfaces degrease first with a solvent degreaser and then with an alcohol degreaser — Quartz Master CB 120 followed by IPA. For polycarbonate and acrylic use isopropyl alcohol only, as other solvents can cloud the surface. The surface must be clean, dry, degreased and non-absorbent; contact with moisture before curing prevents a sound film from forming.
Consumption is approximately 15 ml/m². Decant only the quantity needed and do not return unused material to the original container. Application tools must be clean and completely dry, and applicators must not be reused.
More grades
Browse the full catalogue by category, or send your requirements — we will recommend a grade for your case.
Organic Polysilazane Resins
→
Inorganic Polysilazane / Ceramic Precursors
→
Modified Polysilazane Coatings
→
Ready-to-use Ceramic Coatings
→
High-temperature Ceramic Coatings
→
Electrical Insulation Coatings
→
Fluorosilanes & Surface Modifiers
→
Adhesives
→
Additives
→
Polycarbosilane
→
SiC Fibers
→
Ordering & logistics
Common questions from procurement and engineering teams.
What packaging formats are available?
Standard packaging is 1 kg, 5 kg and 25 kg containers, grade-dependent. Other formats, minimum order quantity, lead times, shipping terms and stock availability are confirmed on request.
What is the minimum order quantity for this product?
MOQ depends on the packaging format — confirmed by our team for your grade and volume.
What happens after I send an inquiry?
Our technical team reviews your requirement and responds with a recommendation, the relevant documents and next steps.
How do I get a quotation?
Include your estimated volume and application in the inquiry — a quotation follows the technical review.
How is the product shipped?
Packaging, transport classification and shipping details are provided per SDS — request packaging and shipping information with your inquiry.